Shivam Electricals Testing Laboratory
100% Calibrated Routine & Type Testing

In-House Testing Facilities & Quality Inspection

Every switchboard manufactured by Shivam Electricals undergoes stringent stage-wise testing in our dedicated test bay before factory release, conforming strictly to IS 8623 (Part I) and IEC 61439 standards.

Electrical Engineers Performing 2kV HV Testing
Certified Quality Control

Calibrated Testing Infrastructure

On the strength of over two decades of engineering experience, Shivam Electricals has always sought to produce switchboards complying with national and international safety codes.

Our in-house testing bay is equipped with calibrated test kits including a 2kV High Voltage Test Kit, 500V/1000V Megger Insulation Testers, Primary Current Injection Kits (up to 2000A), and Secondary Relay Calibration Units.

ISO 9001 Quality Certificate
ISO 9001:2008 / 2015 Certified SystemDocumented test logs and traceable calibration records for every switchboard.
Factory Routine Testing

100% Routine Tests Conducted on Every Panel

Mandatory test protocol executed prior to client factory acceptance test (FAT) or site dispatch.

Inspection of Assembly & Wiring

IS 8623 Part 1

Visual verification of component ratings, phase clearances, creepage distances, terminal numbering, and cable ferrule identification.

Continuity & Circuit Verification

IS 8623 / IEC 61439

Point-to-point electrical continuity testing of all power, control, interlock, metering, and protective relay circuits.

Insulation Resistance (Megger Test)

Tested at 500V / 1000V DC

Measured between phases, phase-to-neutral, and all live conductors to earth before and after high-voltage dielectric application.

High Voltage (HV) Dielectric Test

2 kV AC for 1 Minute

High-voltage stress testing applied across main power circuits and control circuits to prove insulation integrity.

Compliance Standards

Type Tests per IS 8623 (Part I)

Proven switchgear designs certified for short-circuit withstand capacity and continuous thermal rise limits.

IS 8623 (Part I) 8.2.3-1993

Short-Circuit Withstand Test

Rating: Up to 50kA / 65kA for 1.0 second

Verifies the mechanical and thermal strength of busbars and non-hygroscopic supports under extreme short-circuit fault conditions.

IS 8623 (Part I) 8.2.1-1993

Temperature Rise Test

Rating: Continuous Rated Current (up to 6300A)

Monitors thermal rise across main busbars, breaker connection joints, and enclosed air to ensure full compliance with IS limits.

IS 8623 (Part I) 8.2.2-1993

Dielectric Properties & Clearance Verification

Rating: Rated Impulse Withstand Voltage

Ensures adequate electrical clearances and creepage distances across compartmentalized Form 4 barriers.

Specialized Diagnostics

Special & Relay Calibration Tests

Primary Injection Testing

High-current injection up to 2000A to verify current transformer (CT) ratios, polarity, and magnetic saturation thresholds under live loads.

Secondary Injection Testing

Precision electronic injection testing of microprocessor-based and numerical protection relays to verify pickup times and trip curve characteristics.

Electrostatic Powder Coat DFT Verification

Digital magnetic thickness gauge inspection ensuring uniform 70 to 90-micron paint film thickness after baking oven curing.

Mechanical Interlock & Defeat Checks

Rigorous verification of breaker draw-out mechanisms, door interlocks, padlocking provisions, and safety shutters.

Quality Inspection Workflow

6 Stage-Wise Quality Inspection Gates

Total Quality Management (TQM) adhered to across every production phase.

1. Inward Raw Material

CRCA steel sheet thickness check, electrolytic purity of copper/aluminum busbars, and certified switchgear components.

2. CNC Fabrication & Welding

Dimensional tolerance checks, burr-free shearing, precise CNC bending angles, and welded joint strength.

3. 9-Tank Pre-Treatment

Chemical titration checks across degreasing, derusting, phosphating, and passivation baths.

4. Powder Coating & Baking

Visual finish inspection, cross-hatch adhesion testing, and digital DFT coating thickness verification.

5. Assembly & Busbar Bolting

Torque wrench tightening of all busbar joint fasteners with torque seal marking and color-coded PVC sleeving.

6. 100% Routine Testing

High voltage 2kV test, 1000V Megger, primary/secondary injection, and client witness inspection before dispatch.

Schedule a Factory Acceptance Test (FAT)

We welcome client engineers and consultants to witness live testing of their switchboards at our Kalher test facility.